06 STANG custom

[HardKnox]

well ive started a new stang this will be vers 9 and hopefully will get this one more accurate ...and im turbosmoothing ilt 2 ...but alsoim keeping in mind of maybe for games ill save a copy before final turbosmooth ....ok so far concentrating on hood and front fenders little on door..2 1/2 hrs progress and going slow and researching every angle....i will model the body as gt version then start my body kits or tuning ...the wheel is my unfinished saleen wheel from previous version

[NightEye]

When you're researching every angle, you should know your line in the middle of the hood is wrong, the corner above the headlight should be smooth, and that the indent on the doors don't go up untill the sharp edge but it stops earlier

Nice start though.

[HardKnox]

ok hood wasnt welded turbosmooth pushed it up fixed that and didnt notice it...was late last night fixed scallop and not sure what you mean above headlight heres the ref pic i used to shape edge of hood and around headlight only....because of the prespective ...

[KMyers-MG]

Keep at it Tim. I know you'll have it all tweaked up to an awesome end result.

[HardKnox]

heres little progress.....thx for pointing those defects out night eye....still not sure on headlight area cause the lines match the side and front view of my ref photos...need more input there if you still think its wrong

[KMyers-MG]

Nice progress buddy.

[NightEye]

Marked with red, it looks like it isn't smooth as marked green on the refpic
Rest looks better now

[revelli]

cool, love this, nothing to crit except the part that shows NE

[HardKnox]

little more progress moving slow ....tweaked that nighteye see what ya think now...also got old tailights in and lined up so far everythign has been same size and shape that ive merged in from m old stangs....btw ty

[p4vlik.cz]

can u post wire plz?

[NightEye]

Better already, but still a bit sharp where the sharp edge hits the other
And here are some lines and corners to pay attention to

Nice work

[HardKnox]

messed aroudn with those edges and window...front little more whole lot more chamfer fenders hood cut in gas cap...almost ready to start the bumpers....also the sharp flat area isnt eactly flat so rounded it just tad so it is not so flat looking....not sure i wanna post wire ...few tri and more poly than probably needed but didnt wanna use more than 2ilt...i dont usually have problems with tri poly as long as i weld when chamfer it creates small tri poly weld those they work fine....wire is little messy keep jumping around ill get it tho* ... think gonna leave rear alone for now ill try to take me some pictures tomorrow of one to much prespective from what i find on net....soemthing not right around tailight area

[Icetiger01]

Really nice mustang so far!

[HardKnox]

ok remeberr now this first vresion will be custom bumpers lights and what ever i else i do to it ...just incase you think lights or surrounds are wrong...there will be no clear lenses over headlights surrounds but on the headlight them selves

[NightEye]

IMO the lights are a bit small, but it's your styling
Good luck

[HardKnox]

was thinking that also ....can enlarge a little ...heres what im going off of not the grill or bumper just the surround and lights

[HardKnox]

well got started on bumper worked it most of tonight.....look over lights there old and jsut there for visual right now....and every thing is subject to change ..tomorrow i may get on the window treatments and knock those out and mayeb the side skirts....still alot of quirks and tweaking to do around corners and some edges...may cut fog lights n not reall sure at this point we will see...

[HardKnox]

oh also enlarged the headlights a bunch .....heres material preview ....the material off my 34....toned down a little