2009 Nissan GTR

[jms_3d]

Looking good sofar Do you think we could see a new wireframe?
IMO the nissan text on the number/lisence plate comes out too far, it should be more "flush" as it sticks out alot. Thats just an opinion though, its your model

Anyways its looking pretty good sofar and i see your making fast progress

Keep up the good work!!

James

[advan]

If you look here

http://www.smcars.net/forums/182932-post11.html

Pushes out a lot, tokyo motor show model has an even greater extrusion. Wire is messy, but works for me.

[jms_3d]

wires looking goodadvan

I know what you mean about the liscence plate but its just my personal opinion as i think its too atention grabbing but as i say thats just a personal opinion and it is your model

James

[advan]

No problem

[ibeam]

looking nice but you need more edges across the hood (same reasons as i said so about the part in front of the headlight.

regards,
rodder

[kawaiistef]

advan, you're doing a great work.
I post some other refs for you: maybe you may correct several little things...
BTW,keep on the good job!

[advan]

thanks a lot guys! Mind sharing all your refs kawaii? Those are exactly what I need.

[kawaiistef]

Originally Posted by advan

thanks a lot guys! Mind sharing all your refs kawaii? Those are exactly what I need.

All my refs? I've more than 300 pictures of the new GT-R, so it'll be easier to demand me exactly which ref you need.

[advan]

If it isnt too much trouble, maybe all the files in a .zip format? If not, dont worry. Maybe - a lot of shots of the front fender emblem (point which the fender connects to door), vent on the hood, and a whole view of the car, like 10-40 feet away. Thanks again Small update. I promise for bigger update next time

[ibeam]

i think i see a little pinch under the inside lower corner of the headlight.

ibeam

[jms_3d]

Originally Posted by ibeam

i think i see a little pinch under the inside lower corner of the headlight.

ibeam

ibeam where is the pinch? I cant see one to be honest!?!? :?

Model is comming along very nicely, i like seeing a new diffrent model from time to time (gets a bit boring after a while seeing the same models being created) has been quite a few recently

Keep up the good work, it's looking great so far

James

[ibeam]

if you look carefully in the area i circled there's a crease running away from the corner. either that or i'm going crazy.

ibeam

[jms_3d]

hmm i see, mabye a bump not a pinch?

James

[ibeam]

lol, the difference is somewhat insignificant but i'll concede the point. why don't we agree on "issue"?

ibeam

[jms_3d]

a bump is usually easier to fix than a pinch and i do agree with you, there is deffo something there i was just pointout, or rather just asking weather it is a pjnch or just a bump

James

[advan]

hi 2 weeeks later...

I didn't try too hard on those "sphere dots" since i can barely see it from an inch away lol and neither should you! *insert uncle sam picture here*

Next additions are:
- "flat" part of fender
- hood vent

hood vent, i have no clue but to mess around with wire until i get it.

[The IC]

lol...the hood vents...they put em a very inconvenient place for 3d modelling didnt they

[ReKiB_Designs]

Nice Modeling there.

[kawaiistef]

Hey, good progress!
It's not a part easy to model, isn't it?
I'm joining pictures for references...hope it'll help!

[mikolc]

Looking really great man. Keep it up.